LadderCageLadder With Cage — Caged Fixed Ladder, Factory Direct
Ladder With Cage Around It
Ladder with cage fully welded – galvanized, SS304, or custom sizes. Factory-direct price on ladder with cage; quote in 24 hours. OSHA 1910.28 & EN ISO 14122-4 compliant.
Years Manufacturing
Countries Exported
Projects Delivered
Quote Response
Same Product, Correct Term
Ladder With Cage - Options & Materials
A ladder with cage around it is a caged fixed ladder — the same product, the correct term. Fully welded, galvanized or stainless, with hoops and straps engineered to standard.
Hot-Dip Galvanized
Q235B with HDG 85–100 µm per ISO 1461 — the most cost-effective outdoor finish.
Stainless SS304
PMI-tested for chemical, marine and food-grade environments.
Custom Sizes
Any height to 25 m in a single run, custom widths and walk-throughs.
Welded & Engineered to Standard
Ladders With Cages - Specifications
Fully welded stringers and rungs — the parameters below are built into every ladder with cage.
| Specification | Value |
|---|---|
| Rung Diameter | Φ20 mm |
| Rung Spacing | 280 mm (≤300 mm) |
| Clear Width | 500 mm |
| Cage Diameter | Φ700 mm (hoops 40×5 @≤1500) |
| Cage Start | 2.2 m above floor |
| Load Rating | 1.5 kN (≈338 lb) per rung |
| Welding | Fully welded stringers & rungs |
| Material | Q235B HDG / SS304 |
OSHA 1910.28 / EN ISO 14122-4
Ladder With Cage Compliance (OSHA 1910.28 / EN ISO 14122-4)
Compliant with both major standards — and the documents ship with the ladder.
- DoC — OSHA 1910.28 & EN ISO 14122-4
Declaration of Conformity to the relevant standard
- MTC 3.1 Material Certificate
EN 10204 3.1 for Q235B / HDG / SS304
- Structural Calculation Sheet
Engineer-signed for project loads
Factory-Direct Pricing
Ladder With Cage – Factory-Direct Pricing & 24h Quote
No distributor markup — itemized factory-direct pricing on your ladder with cage, quoted in 24 hours.
Factory-Direct
Quote direct from the production floor, no middlemen.
Itemized Quote
Material, welding, finishing and packaging — line by line.
24h Response
Itemized quote within 24 hours; build in 15–25 working days.
Get a Ladder With Cage Quote
Get a Ladder With Cage Quote
Factory-direct pricing and an itemized quote within 24 hours. Tell us height, material and quantity.
- 24h itemized quote
- Fully welded build
- DoC, MTC & structural calcs included
Budgeting a Ladder With Cage From Factory Floor to Your Site
The sticker on a ladder is rarely the last number on the invoice, and buyers who budget only for steel get surprised by accessories and logistics. Factory-direct pricing changes that arithmetic in your favor. Base fabrication for hot-dip galvanized Q235B starts near $95 per meter, so a 6 m unit with its welded cage typically lands between $600 and $900. From there the variables are honest and enumerable: stainless upgrades multiply the base (SS304 about 1.8x, SS316 about 2.5x), landing platforms add $150–400 each, safety gates $60–180, walk-through exit kits $90–250 per set, and sea freight usually runs $280–550 for a 6 m caged ladder.
| Budget line | Typical range | Notes |
|---|---|---|
| Ladder with cage, 6 m HDG | $600–900 | Baseline configuration |
| Stainless upgrade | 1.8x (SS304) / 2.5x (SS316) | Coastal and chemical service |
| Landing platform | $150–400 | Rest points above 6 m routes |
| Safety gate | $60–180 | Top-exit protection |
| Exit guardrail kit + sea freight | $90–250 + $280–550 (6 m unit) | Destination dependent |
For context, US catalogue pricing for comparable caged ladders spans $1,325–7,400 as of August 2026 — the spread factory-direct quoting eliminates. Send the five key facts and the itemized quote within 24 hours becomes your real number.
Field Story — a Grain Dryer Climb That Had Been Dodged for Years
Why an Agro-Processor Finally Bought a Ladder With Cage — and What It Replaced
On farms and feed mills, the climb people avoid is the climb that eventually injures someone. This story is the pattern we see across agro-processing sites in 50-plus countries.
The site had a 12 m grain dryer reached by a welded ladder with no cage — installed decades ago, when the dryer went up. Staff younger than the ladder refused it; the maintenance foreman climbed it monthly with a rope looped over a rung as a makeshift grab line. Dust collection at the top meant the last two meters were always slick with chaff, and everyone knew the ladder was the most dangerous object on site.
The plant manager sent photos of the existing stringers and the bin height. Our engineer proposed a full replacement rather than a cage retrofit — the old welds had no traceable material history, so hanging a new cage on them would transfer the liability, not remove it. The new unit: a 12 m HDG ladder with cage in two bolted 6 m sections, hoops 40×5 at 1500 mm with 30×3 straps, a rest platform mid-climb, and a walk-through exit at the dryer gantry.
At the $95/m HDG rate the ladder itself ran about $1,140 ex-works; platform, exit group and freight brought the landed total into a range the insurer offset against a premium adjustment. Production 15–25 days, quote returned in 24 hours, and the whole climb is now done one-handed with tools — the way it should always have been.
| Before — Field Condition | After — What Was Installed |
|---|---|
| 12 m welded ladder, no cage, no records | 12 m HDG caged ladder in two 6 m bolted sections |
| Rope over a rung as a grab line | Cage Φ700 mm from 2.2 m, hoops 40×5 @≤1500, straps 30×3 |
| No rest point on a 12 m climb | Rest platform mid-climb, walk-through exit at the gantry |
| Untraceable material, uninsurable asset | MTC 3.1, DoC, ISO 5817 C welds, 10-year photo record |
| Rungs slick with chaff near the top | Φ20 rungs at 280 mm, HDG 85–100 μm over every weld |
One Climb, Three Equipment Answers
Ladder With Cage, Bare Ladder With Harness Rail, or Full Stair — the Honest Cutoffs
The choice is not about budget first — it is about who climbs, how often, and what your insurer will accept when they walk the site. Use these cutoffs before requesting any quote.
| Choose | When |
|---|---|
| Ladder with cage | the climb is fixed, multiple people use it, and you want protection built into the steel — cage from 2.2 m means every climber is guarded without a harness program |
| Bare ladder plus fall-arrest rail | only trained, certified staff climb, climb frequency is low, and anchor points exist top and bottom — cheaper hardware, but training and gear inspection move onto your ledger |
| Inclined stair with handrails | the route carries parts, samples or visitors — stairs cost more steel but remove climbing-specific training almost entirely |
| Cage ladder plus rest platforms | the climb exceeds what your standard allows in one flight — EN ISO 14122-4 works to 10 m systems with platforms at 6 m; we splice and platform to suit your exact height |
Mistakes buyers make on their first caged replacement
- Retrofitting a cage onto untraceable steel — if the stringers have no material history, a new cage just moves the liability; replace the climb and restart the paper trail
- Buying on ladder price alone — at $95/m for HDG the ladder is the small number; platforms, gates and freight decide the landed cost you will actually feel
- Ignoring the rest-platform rule for tall climbs — a 12 m single flight fails EN geometry; plan platforms into the drawing, not into the correction notice
- Choosing stainless for dust, galvanizing for rain — match material to the actual corrosion driver: chaff dust needs HDG, chemical splash needs SS304, salt air needs SS316
Drawing to Outcome
Five Specs on Your Ladder-With-Cage Quote — and What Each Earns You
Every row below is a number you will see on our itemized quote, followed by the concrete result it produces on your site after install day.
| Feature | Advantage | Your Outcome |
|---|---|---|
| Rungs Φ20 at 280 mm, 1.5 kN | comfortable boot contact, tool-load rated | climbers carry parts without rung flex or doubt |
| Cage Φ700 from 2.2 m | passive enclosure from the danger height | protection that works with zero user training |
| Bolted 6 m sections | container-legal, two-person install | no crane day, no site welding, no hot-work permits |
| HDG 85–100 μm per ISO 1461 | zinc inside the cage and over every weld | the chaff-and-rain climb stays quiet for a decade |
| 24 h quote from your photos | engineer-checked geometry before payment | you commit to firm numbers, not catalog estimates |