LadderCageSafety Ladder Cages, Factory Direct
Ladder Protection Cage
Safety ladder cage – galvanized, aluminum or FRP, 1.5 kN (≈337 lb) rated, custom heights. Free spec sheet; OSHA 1910.28 & EN ISO 14122-4; test reports and DoC.
Projects Delivered
Countries Exported
Rated Build
Quote Response
Three-Material Matrix
Safety Ladder Cage – Galvanized, Aluminum, FRP
Pick the material that fits your environment — each build is 1.5 kN (≈337 lb) rated and made to custom heights.
Hot-Dip Galvanized
Q235B with HDG 85–100 µm per ISO 1461. Best all-round value for outdoor and industrial use.
Aluminum
Lightweight for frequent handling and retrofits; corrosion-resistant without coating maintenance.
FRP
Fiberglass reinforced plastic — corrosion-proof and electrically insulating for chemical, marine and electrical rooms.
Load Rating & Customization
Safety Ladder Cages – 1.5 kN (≈337 lb) Rated & Custom Heights
Every safety ladder cage is engineered to the parameters below, with custom heights to 25 m in a single run (one-piece max 14 m).
| Specification | Value |
|---|---|
| Rung Diameter | Φ20 mm |
| Rung Spacing | 280 mm (≤300 mm) |
| Clear Width | 500 mm |
| Cage Diameter | Φ700 mm |
| Load Rating | 1.5 kN (≈337 lb) per rung |
| Cage Start | 2.2 m above floor |
| Custom Heights | Up to 25 m single-run (bolted splices; one-piece max 14 m) |
| Materials | Galvanized / Aluminum / FRP |
Test Reports & DoC with Every Order
Safety Ladder Cage Compliance – Test Reports & DoC
No chasing paperwork after delivery — every ladder protection cage ships with its full compliance file.
- DoC — OSHA 1910.28 & EN ISO 14122-4
Declaration of Conformity to the relevant standard
- Test Reports & MTC 3.1
EN 10204 3.1 material certificates for steel, aluminum and FRP
- Structural Calculation Sheet
Engineer-signed for project loads
Factory-Direct, Fast
Safety Ladder Cage – Free Spec Sheet & 24h Quote
Buy direct from the factory — free spec sheet, itemized quote in 24 hours, shipped fast.
Free Spec Sheet
Material matrix and dimensions emailed within 24 hours.
Quick Quote in 24h
Itemized factory-direct pricing, no distributor markup.
Factory-Direct, Shipped Fast
Built on the Dengtai line and shipped on schedule.
Get a Safety Ladder Cage Quote
Get a Safety Ladder Cage Quote
Free spec sheet and itemized quote within 24 hours. Tell us height, quantity and material — galvanized, aluminum or FRP.
- 24h itemized quote
- Free spec sheet
- Test reports & DoC with every order
Matching Safety Cage Material to Service Environment
A safety cage is only as durable as the material decision behind it. Buy hot-dip galvanized steel for an inland pump station and it will outlive the equipment it serves; buy the same cage for a desalination outfall and the hoops will need replacing within a few winters. This matrix ties each service environment to the build we recommend, the verification that applies, and the price effect against the $95/m HDG baseline.
| Service environment | Recommended build | Verification in force | Price effect |
|---|---|---|---|
| Inland, dry or lightly industrial | Q235B steel, hot-dip galvanized | ISO 1461 coating check, 85–100 μm | Baseline $95/m |
| Urban or road-splash exposure | HDG steel, thicker coating verified per batch | ISO 1461 plus 10-year photo baseline | Baseline, no uplift |
| Coastal, pool or high-humidity plant | SS304 stainless hoops and straps | EN 10204 3.1 MTC on stainless heats | 1.8x HDG |
| Marine splash zone, chemical or desalination | SS316 stainless full assembly | EN 10204 3.1 MTC, ISO 5817 Level C welds | 2.5x HDG |
| Live electrical or strong chemical fume | FRP cage sections per inquiry | Project-specific dossier | Quoted per drawing |
Whatever the grade, the cage geometry stays constant — 700 mm diameter, hoops 40×5 mm at 1500 mm, straps 30×3 mm, cage starting at 2.2 m — so swapping material never changes the climbing envelope your workers are trained on.
The Second Axis: Where It Ships
Ladder Safety Cage by Governing Standard — the Jurisdiction Decision
The table above matched material to environment; this one matches geometry to jurisdiction — the second decision every ladder safety cage order has to survive. The regimes differ at exactly three points: the height that triggers the cage, the treatment of long climbs, and the documents at the border. Our standard DNA — 500 mm width, Φ700 mm cage, rungs Φ20 @ 280 mm, cage from 2.2 m — clears all four regimes, so the jurisdiction question changes the paperwork and the platform count, not the climb your workers are trained on.
| Where the Site Sits | Governing Rules | Cage Trigger | Order Notes |
|---|---|---|---|
| United States | OSHA 1910.23 and 1910.28 | 24 ft | imperial dual dimensions; exemption dated 2036-11-18, 2025-09 proposal still undecided — cages remain the path |
| European Union | EN ISO 14122-4 | 3 m | rest platform at 6 m, flight ceiling 10 m; DoC drafted in parallel with the drawing |
| Australia | AS 1657 | 3 m | metric masters, cage from 2.2 m already inside the envelope |
| United Kingdom | BS 4211 | 3 m band | BS geometry matches our DNA — no variant drawing needed |
| Multi-jurisdiction fleet | any mix of the four | strictest applies | one master drawing, per-site DoC set — the 10-year archive keeps them aligned |
| The Jurisdiction Error | Where It Bites | The Discipline |
|---|---|---|
| OSHA ladder shipped to an EU site | 24 ft thinking against a 3 m line — rejection at inspection | state the site country in the RFQ; we dimension to the governing standard |
| EN climb ordered without the 6 m platform | compliant cage, non-compliant tower | platform $150–400 at the interval — one weldment, one file |
| Projects paused on the OSHA proposal | dates slip for a rule with no decision date | build to the standing regime; the cage stays compliant either outcome |
| Four vendors for four jurisdictions | four geometries, four training briefs, four files | one DNA fleet-wide — only the paperwork localizes |
Feature to Outcome
One Safety Cage, Two Decisions Already Made for You
Material matched to air, geometry matched to jurisdiction — five rows that carry both decisions into evidence.
| Feature | Advantage | Your Outcome |
|---|---|---|
| Environment matrix applied before quoting | HDG $95/m, SS304 1.8x, SS316 2.5x aimed by air, not habit | the metal bill matches the atmosphere, every meter |
| Geometry that clears four regimes | 500 mm width, Φ700 mm cage, 2.2 m start | one drawing set serves every site you own |
| Per-jurisdiction DoC set | OSHA, EN, AS and BS paperwork drafted with the drawing | border and inspection days carry no surprises |
| Verification written into the order | MTC 3.1, zinc reports, PMI on stainless, calcs signed | every material claim arrives with its own proof |
| 24 h quote, MOQ 1, 15–25 day build | pilot then rollout on the same DNA | site-wide standardization decided on installed evidence |
Verify Any Supplier in Five Checks
The Five-Check Walkthrough: Reading a Safety Cage Quotation Like an Inspector
A safety cage quotation is a set of claims, and claims are checkable. The five checks below are the ones our own dossier has to survive — run any quote, ours included, through them in order. A quotation that passes all five is a cage you can put people on; each failure is not a discount, it is a missing layer of proof you will reconstruct later at a higher price.
| Check | The Claim to Test | What Passing Looks Like | What Failing Means for You |
|---|---|---|---|
| 1 — Geometry against the envelope | Cage diameter, hoop section and spacing, strap size, start height | Φ700 mm, hoops 40×5 mm at 1500 mm, straps 30×3 mm, cage from 2.2 m — stated as numbers | Vaguer figures mean skinnier steel; the restraint is only as good as the thinnest member |
| 2 — Material identity | Steel grade with a paper trail | EN 10204 3.1 MTC per batch, grade named | No certificate, no defensible load rating — treat as replace, not repair |
| 3 — Fabrication quality | Welds made under control, not over a weekend | Weld inspection records to ISO 5817 Level C | Uncontrolled welds are the failure point nobody photographs |
| 4 — Corrosion budget | Coating thickness measured, not promised | Hot-dip galvanized to ISO 1461 at 85–100 μm | Thin coating is a five-year repaint wearing a thirty-year price |
| 5 — Assembly proof | The sections fit before they shipped | Trial assembly performed, photos archived | First fit happens on your wall, on your schedule, on your crane |
Every Dengtai quotation is written to pass this walkthrough — geometry stated, MTC attached, weld records referenced, coating certified, trial photos on file for 10 years. Run a competing quote through the same five checks and send us the scorecard: the free spec sheet comparison comes back within 24 hours.
Material, Scope and Source
Reader Decision Guide: Choosing the Safety Cage Material, Scope and Supplier
Three decisions complete a safety cage order, and all three are about honesty — with the environment, with the existing steel and with the supplier. The material matrix earlier matched the cage to the air; this guide handles what that matrix cannot: how much cage to order, and who deserves the order.
Full ladder or cage the existing one
If the existing ladder is sound, traceable and dimensionally standard, a cage order against measured rails can work — send photos and measurements and we state honestly whether it qualifies. If the rails are unknown steel or improvised geometry, the ladder is the weak layer under a new cage — order the complete assembly and let one file cover both.
Match the material to the worst season
Choose by the harshest month the site sees, not the average: splash-zone winters pick SS316 at 2.5×, pool and process air picks SS304 at 1.8×, everything else is served honestly by HDG at $95 per metre. The coating you need is the one working in February, not the one quoted in June.
Buy from whoever survives the walkthrough
Run every candidate — including us — through the five checks above. The supplier who states geometry as numbers, attaches the MTC, references the weld code, certifies the coating and proves the trial assembly is the supplier whose cage is still a safety system in year ten. Price decides between equals; it should never decide between proofs.
Measurements ready? Send them with a photo of the host ladder and the free spec sheet arrives with the honest verdict — cage-only or complete, priced both ways, inside 24 hours.
Proof With the Steel
What Each Feature of a Dengtai Safety Cage Returns
Five features — one for every check in the walkthrough.
| Feature | Advantage | Your Outcome |
|---|---|---|
| Geometry printed as numbers | every envelope value stated on the approval drawing | check 1 passes before you commit a currency |
| Batch-traceable MTC 3.1 | steel identity documented heat by heat | check 2 closed with the invoice, not after an incident |
| ISO 5817 Level C weld records | fabrication quality written down, not asserted | check 3 answered by a document auditors accept |
| ISO 1461 coating certificate | 85–100 μm measured at the dip, not hoped for | check 4 becomes a number in your maintenance file |
| Free spec sheet comparison | our quote scored beside any competitor | the order goes to proof, and you keep the evidence |