LadderCageCage Ladder DWG Drawings
Cage Ladder DWG Drawings
Standard cage ladder DWG drawings with full dimensions — the full DWG set with every quote, zero charge; DoC, MTC and HDG report with the drawing set.
Projects Delivered
Countries Exported
Response Time
Max Single-Run Height
Standard DWG Drawings
Cage Ladder DWG – Full Dimensions
A standard cage ladder DWG set with full dimensions — elevation, plan, section and detail views ready for your project file.
- Full Dimensioning
Rung spacing, clear width, cage hoops, flared entry and fixings
- DWG / DXF / PDF
Delivered in the format your drafting team needs
- Standard Drawing Set
Based on OSHA 1910.28 / EN ISO 14122-4 configurations
| Specification | Value |
|---|---|
| Rung Diameter | Φ20 mm |
| Rung Spacing | 280 mm (≤300 mm) |
| Clear Width | 500 mm |
| Cage Diameter | Φ700 mm (hoops 40×5 @≤1500, straps 30×3) |
| Cage Start | 2.2 m above floor |
| Load Rating | 1.5 kN per rung |
| Max Height | 25 m single run |
| Entrance | Flared / flared splay entry |
Zero Charge
Free DWG Set with Every Quote
Full Set, Zero Charge
The complete DWG drawing set ships with every quote — no fee, no sign-up.
No Account Needed
Request the set directly — we send it with your itemized quote.
24h Response
DWG set and quote delivered within 24 hours of your request.
Documents Included
DoC, MTC & HDG Report Included
The full drawing set is paired with the compliance file your project needs — no chasing paperwork.
- DoC — OSHA 1910.28 & EN ISO 14122-4
Declaration of Conformity included
- MTC 3.1 Material Certificate
EN 10204 3.1 for Q235B / SS304 / SS316
- HDG Report
Coating thickness report for hot-dip galvanized finish
Request the Full Set
Request the Full DWG Set
500+ projects shipped across 50+ countries — request the standard DWG set and get your quote in the same message.
Request the Full DWG Set
Get My Cage Ladder DWG Set
Standard DWG drawings with full dimensions, zero charge with every quote, plus DoC, MTC and HDG report. Sent within 24 hours.
- Full DWG set — zero charge
- DWG, DXF & PDF formats
- DoC, MTC & HDG included
- 24h response
Inside the Free CAD Proposal
Every Sheet in the DWG Package — and Who Uses It
A cage ladder drawing set is not one file; it is a small document library that keeps your engineer, installer and inspector working from the same geometry. This is exactly what we issue with every free CAD proposal, in DWG, DXF and stamped PDF.
| Sheet | Contents | Who Uses It |
|---|---|---|
| General arrangement | Overall heights, cage extent, platforms, datum levels | Your engineer — approval and clash review |
| Elevation | Stiles, rung line at 280 mm, splice positions | Installer — what the ladder looks like bolted up |
| Cage section | Φ700 mm barrel, hoops 40×5 at 1500 mm, straps 30×3 | Inspector — enclosure compliance check |
| Anchor detail | Bolt grid, standoff brackets, torque values | Concrete or steel fixing crew |
| Entry and exit details | Flared entry, walk-through or step-off top | Installer and safety officer |
| Bill of materials | Part marks, lengths, finishes per piece | Procurement and goods-in check |
Because the same package drives quoting, fabrication and inspection, dimension errors surface at the drawing stage — before steel is cut, not on your site. Request the free CAD proposal with your height and material, and the full sheet set above arrives within 24 hours.
Your Side of the Drawing Exchange
What You Send Determines What You Get — the Input Decision Table
The deliverables table above shows what leaves our office. This one governs what arrives at it. Buyers lose time not on our 24 hours, but on the inputs — a sketch that misses one anchor dimension sends the whole loop around again. Match your situation to the row, send what the row asks, and the free CAD proposal lands complete on the first pass, in DWG, DXF or PDF as your team works.
| Your Situation | Send Us This | You Receive in 24 h |
|---|---|---|
| New access, nothing drawn yet | climb height, structure type, five site photos | full CAD proposal from our standard DNA — rung Φ20 @ 280, width 500, cage Φ700 |
| Existing DWG or DXF from another supplier | the file plus your mark-ups | revised drawing with our geometry and an itemized quote against it |
| Standards-driven project, EN or OSHA regime | the governing standard and site country | drawing dimensioned to the right regime, DoC drafted in parallel |
| Retrofit against an old installation | photos of the anchors plus a tape measurement | proposal with bracket detail matched to what is actually in the wall |
| Repeat of a ladder we built before | your original order reference | drawings pulled from the 10-year archive, quoted in hours |
| The Input Mistake | What It Costs Later | Prevention |
|---|---|---|
| Paying a draftsman for proposal drawings | fees for work we produce free, before and after revision | every DWG, DXF and PDF proposal is no-charge, no-commitment |
| Height given as "about 6 m" | sections cut to the wrong length — rework or splice on site | send the tape measurement and one photo with a scale reference |
| PDF-only exchange kept as the master | dimensions frozen in print, unmarked-up when the site changes | we keep native CAD as master; your PDF stays a controlled copy |
| Anchor and obstruction details left off | brackets that suit a drawing, not your wall | shoot the five-photo set — mounting face, full height, condition, obstructions, anchor point |
Feature to Outcome
Five Drawing Services That Save More Than They Cost — and They Cost Nothing
Each row removes a step your project used to pay someone else for.
| Feature | Advantage | Your Outcome |
|---|---|---|
| Free CAD proposal in DWG / DXF / PDF | native files your team can mark up | zero drafting spend before commitment |
| 24-hour drawing turnaround | proposal, revision and quote on the same clock | tender deadlines met without overnight miracles |
| Drawings archived 10 years | your geometry retrievable long after the project team moves | extensions and repeat orders quote from file, in hours |
| Standards applied at the drawing stage | OSHA 1910.28, EN ISO 14122-4, AS 1657, BS 4211 built into the lines | compliance reviewed before steel, not after inspection |
| One drawing set driving everything | quoting, fabrication, trial assembly and DoC share the same geometry | what you approved is provably what shipped |